When desaturation is detected, the hybrid gate driver performs a soft shutdown of the IGBT and starts a timed t timer 1. The power dissipation can be estimated using equation 4 from Table 2. Generally, it is a good idea to select a capacitor with a maximum ripple current rating larger than the calculated current. Mouser Electronics har inaktiverat TLS 1. Please upgrade your browser version or settings to restore access to the Mouser website. Isolated gate-drive power is produced by an integrated dc-dc converter, and control signals are isolated using high-speed optocouplers. For the PDF version of this article, click here.

Uploader: Mazur
Date Added: 28 July 2013
File Size: 10.20 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 99144
Price: Free* [*Free Regsitration Required]

Typically, larger igbt module with gate will require a smaller R G and smaller modules will use a larger R G. However, in some low-frequency applications, it might be desirable to use a larger series gate-resistor to slow the switching of the IGBT, reduce noise and limit turn-off transient voltages. In most applications, pin 6 will be tied directly to the 5-V logic power supply. The gate-driver data sheet provides typical curves that can be used to calculate the required supply current for a given application.

Power Electronics brought to you by. In this igbt module with gate, C S can be omitted.

To deliver an efficient pulse current, iggt output of the isolated dc-dc converter must be decoupled using a combination of low impedance electrolytic and film capacitors. More information about text formats.

Hybrid ICs Drive High-Power IGBT Modules

In addition, a BG2A gate-drive reference design is igbt module with gate for prototype evaluation. If the gate driver’s short-circuit protection is activated, it will immediately shut down the gate drive and pull pin 28 low to indicate a fault.


When measuring RMS gate current, be certain the test instrument has a sufficiently high sampling rate to accurately resolve the relatively narrow gate current pulses. Therefore, devices with a minimum 1-W rating are recommended. Desaturation wit be detected by a logical AND of the driver’s input signal and the comparator’s igbt module with gate. A completely isolated gate-drive circuit is most effective for meeting these requirements.

Mouser Access Denied

Igbt module with gate feature igbt module with gate the gate driver to provide completely floating gate drive that is suitable for high- or low-side switching. Web page addresses and e-mail addresses turn into links automatically.

This optoisolated fault signal now can be used by the controller to detect the fault condition. It is important that these capacitors have low enough impedance and sufficient ripple current capability to provide the required high-current gate-drive pulses.

The two drivers are similar except that the VLA uses a standard open-collector type optocoupler with a maximum turn-off propagation delay of about 1.

This makes it suitable for lower frequency industrial applications operating at up to about 15 kHz.

The igbt module with gate driver requires a single V control power supply V D to power its internal circuits. The Zener diode DZ1 provides additional protection of the gate driver’s detect input from voltage surges during reverse recovery of the high-voltage blocking diode.

Test your settings by visiting www. The V power supply is connected to the primary side of the hybrid gate driver’s built-in dc-dc converter at pins 1, 2 and 3, 4. The ripple current in the decou-pling capacitors C2, C3 igbt module with gate be estimated using equations 2 and 3 from Table 2.

Related Posts  K8MM-V VGA DRIVER

In this case, at least a 3-W resistor is required.

The circuit operates from a 15V supply that must be decoupled with a capacitor closely connected to the driver’s pins, providing a stable, well-filtered voltage for the primary side of the driver’s built-in dc-dc igbt module with gate.

The only penalties for using larger than necessary capacitors are their size and cost. This protection scheme avoids the need for a high voltage detection diode, reduces spacing requirements on the gate driver’s p.

ISO5500EVM: Isolated IGBT/MOSFET Gate Driver Evaluation Module

Igbt module with gate page addresses and e-mail addresses turn into links automatically. The gate driver must produce high peak current for efficient switching and have stable driving voltages for good noise immunity and short-circuit durability. Mouser Electronics ha disabilitato il TLS 1. The gate-drive current is adjusted by selecting the appropriate series gate resistance R Gand connecting it between pins 23, 24 and the gate of the IGBT Fig.

Lines and paragraphs break automatically. Nur Wit, die TLS 1.